光澤特性：1、印上就烤顯平光               2、印上放置3小時再烤為干燥后為亮光使用方式：絲印、移印。油墨與固化劑添加比例為10：1，表干15-30分鐘。金屬產品烘烤120-150°C，30分鐘后可完全干燥。玻璃產品烘烤100-120°C，30分鐘完全干燥。強化亞克力及uv表面等塑膠產品烘烤80-100°C，30分鐘完全干燥。測試：產品從烤箱拿出來完全冷卻之后可進行相應測試。         1.  劃百格后使用3M膠紙拉，無掉色，脫落現象。         2.  使用99%無水酒精，500g力來回摩擦1000次，無變色，脫色等現象；         3.  使用25%的鹽酸，500g力來回摩擦一千次，無脫落，變色、脫色等現象；         4.  使用25%氫氧化鈉溶液，500g力來回摩擦一千次，無脫落、變了、脫色等現象；         5.  使用100°C熱水浸泡三小時，拿出后用手擦，無脫落，掉色等現象。適用范圍：            各種金屬制品，玻璃制品，鋼化玻璃（6H以下硬度），鍍膜鏡片，強化亞克力，UV噴油表面等產品。環保檢測：通過歐盟ROHS檢測標準，EN-71等檢測標準，環保保證產品。Gloss characteristics: 1, printing on plain grilled significantly2, printed on the place for 3 hours and then baked for the dry lightUse: screen printing, pad printing. Ink and curing agent to add the ratio of 10:1, the table to do 15-30 minutes. Metal products bake 120-150 degrees C, 30 minutes after the c o mplete drying. Glass products bake 100-120 degrees C, 30 minutes c o mpletely dry. To strengthen the surface of UV and acrylic plastic products such as baking 80-100 ~ C, 30 minutes to dry c o mpletely.Test: the product can be taken out of the oven after the c o mplete cooling can be carried out the corresponding test.The 1 row grid after using 3M tape pull, no fade, shedding.2 the use of 99% anhydrous alcohol, 500g force back and forth friction 1000 times, no discoloration, discoloration and other phenomena;3 using 25% hydrochloric acid, 500g force back and forth friction one thousand times, no shedding, discoloration, discoloration and other phenomena;4 using 25% sodium hydroxide solution, 500g force back and forth friction one thousand times, no shedding, changed, decolorization and other phenomena;5 the use of 100 DEG C hot water for three hours, take out after the hand rub off, discoloration and other phenomena.Scope of application:All kinds of metal products, glass products, tempered glass (6h following hardness), coated lenses, strengthen acrylic, UV injection surface products.Environmental testing: through the EU ROHS testing standards, EN-71 and other testing standards, environmental protection products.